Z-microsystems 14 Bedienungsanleitung

Doc# 27-0001UM Issued 7/99 Rev. 1.2Z MicrosystemsCOMMANDCONSOLE14User ManualFIELD-READY

Doc# 27-0001UM Issued 7/99 Rev. 1.2Loosen the screws oneach of the front Z-Lockmounts.FINAL ADJUSTMENTS OF THE COMMAND CONSOLESlide the Console

Doc# 27-0001UM Issued 7/99 Rev. 1.2Close the storage traytop, then place thekeyboard and mouse ontop of the tray door.Using both hands,gently lift

Doc# 27-0001UM Issued 7/99 Rev. 1.2Place the keyboard andmouse inside the trayalong with all cablesand close door.Using both hands,gently drop the

Doc# 27-0001UM Issued 7/99 Rev. 1.2OperationSwitch the Consolemonitor on by pushingand releasing the powerswitch marked.Turn on the monitor andthen

Doc# 27-0001UM Issued 7/99 Rev. 1.2Monitor AdjustmentsThe LCD monitor features an On-Screen Display (OSD) with menusdesigned to make adjusting themo

Doc# 27-0001UM Issued 7/99 Rev. 1.2MENU DESCRIPTIONSAUTO ADJUSTMENT Select this control to adjust the sizeand position automatically. It takes

Doc# 27-0001UM Issued 7/99 Rev. 1.2Monitor AdjustmentsMENU DESCRIPTIONSH-SIZE Select this control, then use the and buttons to expand ordecreas

Doc# 27-0001UM Issued 7/99 Rev. 1.2AUTO CALIBRATION PROGRAMThis program cooperates with FPMCfirmware which automatically adjustsand saves the pane

Doc# 27-0001UM Issued 7/99 Rev. 1.2ReferenceLED INDICATORThe Power Management feature of theLCD monitor is comprised of threestages:1. On (green)2.

Doc# 27-0001UM Issued 7/99 Rev. 1.2TIMING GUIDEThe monitor is not limited to thesepreset factory-timing modes. In fact,because the monitor is mult

Doc# 27-0001UM Issued 7/99 Rev. 1.21. Use the power andvideo cables suppliedwith the CommandConsole to helpprevent interferencewith radio andtelevis

Doc# 27-0001UM Issued 7/99 Rev. 1.2TroubleshootingNO POWER  Flip the Power switch ON. ThePower LED turns on. Make sure the A/C power cord isse

Doc# 27-0001UM Issued 7/99 Rev. 1.2DOUBLE (SPLIT) SCREEN IMAGE  Make sure the graphics card is setto Non-Interlaced mode. Make sure the input

Doc# 27-0001UM Issued 7/99 Rev. 1.2Specifications22Power 100 - 240 VAC, 47 - 63Hz, 1.2 A MaxWeight 26 lbs.Colors 262,144Viewing Angle L/R 45/45 Deg

Doc# 27-0001UM Issued 7/99 Rev. 1.2Appendix23PIN ASSIGNMENT

Doc# 27-0001UM Issued 7/99 Rev. 1.2NOTE: For image problems, runAUTO SETUP again beforeconsulting this section. Inmost cases, AUTO SETUP canfix the

Doc# 27-0001UM Issued 7/99 Rev. 1.2If the Z Microsystems TechnicalSupport Engineer determines that theproduct needs to be replaced, aCustomer Servic

Doc# 27-0001UM Issued 7/99 Rev. 1.2Y2K COMPLIANCEZ Microsystems has achieved full Y2K Compliance.In late 1997, the companys senior management assig

Doc# 27-0001UM Issued 7/99 Rev. 1.2Drawings27

Doc# 27-0001UM Issued 7/99 Rev. 1.2Drawings28

Doc# 27-0001UM Issued 7/99 Rev. 1.2INSTALL HARDWARE· Install the slide assemblies to the rack by installing three screws (V) to thefront and thre

Doc# 27-0001UM Issued 7/99 Rev. 1.2STARTING POINT 4Shipment Contents 4User Manual 4System Requirements 4Product Description 5PREPARATION 6INSTALL

Doc# 27-0001UM Issued 7/99 Rev. 1.2

Doc# 27-0001UM Issued 7/99 Rev. 1.2

Doc# 27-0001UM Issued 7/99 Rev. 1.2Z Microsystems, Inc.5945 Pacific Center Blvd., Suite 509San Diego, CA 92121Phone: (858) 657-1000Fax; (858) 657-

Doc# 27-0001UM Issued 7/99 Rev. 1.2The User Manual comes in twoformats: printed hardcopy or CD-ROM. This Manual is also availableon the Z Microsyst

Doc# 27-0001UM Issued 7/99 Rev. 1.2PRODUCT DESCRIPTIONThe CommandConsole providesa liquid crystaldisplay, a deskwork surface andstorage for anysize

Doc# 27-0001UM Issued 7/99 Rev. 1.2TOOLS REQUIREDPRECAUTIONS Required Tools and Equipment Flathead screwdriver with about 10"shaft. Phillips

Doc# 27-0001UM Issued 7/99 Rev. 1.2SLIDE REMOVALWith the Console sittingon a workbench with thefront facing towardsyou, press down torelease the Z-

Doc# 27-0001UM Issued 7/99 Rev. 1.2Install RailsGo back on the rear ofthe cabinet frame, andfully tighten the threePhillips screws ((W) seepage 30

Doc# 27-0001UM Issued 7/99 Rev. 1.2INSTALL THE COMMAND CONSOLE IN THE SLIDESPull the two Consoleslides out until they lock.Hold the Console by